Tenda O6 Point-to-Point Outdoor 10km Long Range Wireless Bridge CPE (Extends WiFi & Wired Network)
Many people online are searching for the best and longest range outdoor Wi-Fi extenders out there on the Internet. But with hundreds of result you won't even know what's right for you. Some comes in cheap, while some seems over-priced for it's advertised features - which are basically common (ie; Gigabit Ethernet, 2.4GHz WiFi, etc) to all known routers/extenders on the Internet. And in the end, it's not even the right solution to your wireless networking needs.
If you're looking to extend your current network, or setup a remote Access-Point, or connect to a Wi-Fi Access point 10Km away, or create a bridge between two networks wirelessly and cheaply, then most probably the Tenda O6 is what you should look for. Using it, you can connect two LAN wireless at a great distance. You can share your broadband connection from your house to your friend's house - or from point A to point B.
The Tenda O6 5GHz 11AC N433 Outdoor Point to Point CPE, is neither a router nor a wifi expander, though it can function as such. O6 is an ultra long range wireless network bridging device, specially designed for remote wireless networking solution. The range of this particular model, can cover a distance of up to 10 Kilometers. While the Tenda O3 model reaches up to 5 Kilometres long.
- NOTE 1: The O6 and O3 on the model number is spelt with an
O- capital letter O.
- NOTE 2: You need two of these when doing a wireless bridging. Where one should act as the sender, while the other as receiver.
It features an external power amplifier and a built-in 16dBi directional antenna to provide an efficient way to pick up and maintain a stable wireless signal. More of its features are listed below.
Difference Between O6 & O3 Model
See below table for a quick overview of the main difference between these Tenda network bridging device.
|Tenda O6 vs O3|
|Wireless Speed||802.11n (150Mbps)||802.11ac (433Mbps)|
|Antenna Gain||12dBi directional antenna||16dBi directional antenna|
|Ethernet Port||2 x 10/100Mbps Ethernet Port||1 x Gigabit Ethernet PoE/WAN/LAN port|
- 10Km+ Wireless Data Transmission
- 5GHz 11AC 433Mbps
- With Gigabit Ethernet Ports
- IP64 waterproof enclosure
- 16dbi directional antenna
- AP, Station, WISPoperating mode supported
- Up to 60 meters (of Ethernet Cable) of flexible deployment with included PoE Injector
- Easy to Setup, Bridge two device at a push of button
- Smart LED Signal Indicator
- Long-distance Wireless Connection: For a long distance cable-less data transmission, you need to set one device in AP mode, while the other should be in Station mode.
- WISP (Client + Router) Mode: Share your Internet connection from a remote location wirelessly to a local wireless/wired network by connecting the client device to the O6 device running as WISP station or hotspot.
- P2MP Link: Creating a Point-to-multi-point network (P2MP) by linking multiple AP, and all associated wireless clients are able to communicate with each other.
Sample Application 1
Sample Application 2
Sample Application 3
Default Admin Login Credentials
Below is the default and known login details for the Tenda O6 model.
- IP Address:
- Login Username:
- Login Password:
If all else fails, you can check on the label located on the rear panel of your device.
Below is the full technical specification.
|Dimension||270 x 94.86 x 67.5mm|
|CPU Processor||Broadcom 800MHz|
|Maximum Wireless Speed||433Mbps|
|Interface||1 x Gigabit Ethernet Port for WAN/LAN/PoE|
|Operating Mode Switch||Station: The device only works in Station Mode|
|AP: The device only works in AP Mode|
|Off: The device works on AP/Station/Universal Repeater/WISP/Router-Mode|
|Reset: Press 10 seconds or more to restore to default settings|
|Button||Bridge: Press 3 seconds and release it to bridge uplink AP|
|Antennas||16dBi Directional Antenna|
|Antenna Beamwidth||Horizontal: 30°, Vertical: 15°|
|Maximum Power Consumption||9W|
|Power Supply||24v 0.5A PoE Injector|
|Operating Mode||AP/Station/WISP/Router/Universal Repeater/|
|Standard & Protocol||IEEE 802.11ac/n/a|
|Enable/Disable Wireless Radio|
|Wireless Access Control|
|Wireless Client Isolation|
|Wireless Client list|
|Wireless Security||64/128 WEP, WPA-PSK, WPA2-PSK, WPA2-PSK, WPA, WPA2|
|Transmit Power||Adjustable power by 1dBm|
|VPN Pass-through||PPTP, L2TP|
|Remote Web access||Supported|
|Network Diagnoses||Ping, Trace-route, Signal Scan|
Time & Date Setting|
|Temperature||Operating Temperature:-20℃ ~ 55℃|
|Storage Temperature:-40℃ ~ 70℃|
|Humidity||Operating Humidity:10%~90% non-condensing|
|Storage Humidity:10%~90% non-condensing|
Below are labelled illustration of the various parts of the O6 Device.
The Front Panel
|1||GND||Use to protect the device from surge and lightning. Connect the GND port to a grounding bar/rod of a building/house, with a grounding cable and fix it using the included ground screw.|
|2||OFF/STA/AP||Used to adjust operation mode of the device.|
|OFF||Is the Default Option. When it is in OFF position, you can change the operation mode through the Web UI|
|STA||When it is on STA position, the device only works at station mode and you can’t change the operation mode through the Web UI.|
||AP||When it is on AP position, the device only works at AP mode and you won’t be able to change the operation mode through the Web UI.|
Use to bridge two devices or reset the device.|
To bridge two devices:
1. Press and hold this button for 3-7 seconds, when operating under AP mode. When you release the button, LED1 / LED2 / LED3 starts blinking.
2. Within two minutes, press and hold this button for 3-7 seconds on another O6 device, that is operating under Station Mode. When you release the button, LED 1-3 of both devices will light-off and when they light on and keep steady, it indicates that the two devices were bridged successfully.
|RST (Reset)||Resetting the O6 Device: Press and hold this button for over 15-seconds to rest the device to factory default.|
|4||PoE||This port should connect to a Power-over-Ethernet adapter to provide power to the device and transmit data, both at the same time.|
|LAN/WAN||It works interchangeably as a WAN port in router-mode, or as a LAN port in other modes.|
|5||Ethernet Cable Slot||Used to let the cable through, for a snug fit installation.|
The Rear Panel
LAN / WAN|
|Off||Device is powered off.|
|Solid||Device Is off and not transmitting data.|
|Blinking||Device is on and is transmitting data.|
(Signal Threshold LED)
|Off||The device does not bridge to another device.|
|Blinking||The bridging between two devices is in progress.|
When two devices bridge successfully, LED1/LED2/LED3 keeps solid. The three LEDs indicate the signal strength of the other bridged device. By default, the relations between the signal strength and LEDs are shown below, and you can modify each LED’s threshold on the web UI.|
When you unbox the Tenda O6, you would see the following items included. See image below.
How & Where to Buy?
To buy the Tenda O6 Wireless Bridge Device, you can drop by our store (by appointment only) located at Novatel Communication, 24 Main Street, Buttevant, Co. Cork, Ireland.
To purchase online, simply click on the Add to Cart button, and then go through the fast, easy and secure checkout process. Payment is provided for your convenience via Stripe Payment Gateway. You can use any card supported by it (MasterCard, Visa, Amex, JCB, etc).
How Will My Order Be Delivered?
Your order(s) will be shipped via express delivery and are normally delivered within 1-4 business days. Your order will be dispatched directly from our warehouse and you will be provided a tracking information for your order, after it is dispatched. If you have any questions on your order status, please contact us.